AXLE AND DIFFERENTIAL FRONT AXLE HUB REMOVAL
CAUTION / NOTICE / HINT
- HINT:
- ·
Use the same procedure for the RH side and LH side.
·The following procedure is for the LH side.
PROCEDURE
1.REMOVE FRONT WHEEL
43502H 2.REMOVE FRONT AXLE SHAFT NUT
for 2NZ-FE: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 2NZ-FE)>REMOVAL
for 1ZR-FE, 2ZR-FE: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 1ZR-FE, 2ZR-FE)>REMOVAL
47313J 3.SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)
Remove the bolt and separate the front flexible hose from the front shock absorber assembly.
89543 4.SEPARATE FRONT SPEED SENSOR (w/ ABS)
Remove the 2 bolts and separate the front speed sensor wire and front flexible hose from the front shock absorber assembly and steering knuckle.
- NOTICE:
- ·
Be sure to separate the front speed sensor from the front shock absorber assembly completely.
·Prevent foreign matter from contacting the sensor tip.
·Be careful not to damage the front speed sensor.
·Clean the front speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.
5.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
43512 6.REMOVE FRONT DISC
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>REMOVAL
45047 7.SEPARATE TIE ROD END SUB-ASSEMBLY
48069 8.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.
43420 9.SEPARATE FRONT DRIVE SHAFT ASSEMBLY
*a | Matchmark |
Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
- NOTICE:
-
Be careful not to damage the drive shaft boot.
- HINT:
-
If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.
10.REMOVE FRONT AXLE ASSEMBLY
Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.
- NOTICE:
- ·
When removing the nuts, keep the bolts from rotating.
·Be careful not to damage the drive shaft boot.
43340A 11.REMOVE FRONT LOWER BALL JOINT ASSEMBLY
43502G 12.REMOVE FRONT AXLE HUB HOLE SNAP RING
Using snap ring pliers, remove the front axle hub hole snap ring.
43502C 13.REMOVE FRONT AXLE HUB SUB-ASSEMBLY
Secure the front axle assembly between aluminum plates in a vise.
- NOTICE:
-
Do not overtighten the vise.
Using SST, remove the front axle hub sub-assembly.
- SST
- 09520-00031
*a | Bearing Inner Race (Outside) |
*b | Turn |
*c | Hold |
Using SST, remove the bearing inner race (outside) from the front axle hub sub-assembly.
- SST
- 09950-40011 (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010 (09951-00370)
47782 14.REMOVE FRONT DISC BRAKE DUST COVER
Remove the 3 bolts and front disc brake dust cover from the steering knuckle.
43502E 15.REMOVE FRONT AXLE HUB BEARING
Place the bearing inner race (outside) on the front axle hub bearing.
Using SST and a press, remove the front axle hub bearing from the steering knuckle.
- SST
- 09223-15020
09387-02010
09950-70010 (09951-07100)
09950-60010 (09951-00640)