SLIDING ROOF / CONVERTIBLE SLIDING ROOF SYSTEM OPERATION CHECK
CHECK AUTO OPERATION FUNCTION
- NOTICE:
- ·
Make sure that initialization has been completed before inspection.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
·The sliding roof auto operation can be customized. Make sure that the auto operation is ON.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>CUSTOMIZE PARAMETERS
- HINT:
-
When pressing a switch for 0.3 seconds or less, the roof glass moves but auto operation does not operate.
Turn the ignition switch to ON.
When the roof glass is fully closed, press the OPEN switch for 0.3 seconds or more. Check that the roof glass automatically slides until it reaches the comfort stop position.
When the roof glass is in the comfort stop position, press the OPEN switch again for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully opened.
When the roof glass is fully open, press the CLOSE switch for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully closed.
When the roof glass is fully closed, press the UP switch for 0.3 seconds or more. Check that the roof glass automatically tilts up until it is fully tilted upward.
When the roof glass is fully tilted up, press the DOWN switch for 0.3 seconds or more. Check that the roof glass automatically tilts down until it is fully tilted downward.
When the auto function is operating, check that pressing any of the switches on the sliding roof switch (map light assembly) stops the roof glass operation.
CHECK KEY-OFF OPERATION FUNCTION
- NOTICE:
-
Make sure that initialization has been completed before inspection.
-
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Turn the ignition switch from ON to off, and check that the sliding roof can be operated. Then open the driver or front passenger door once, and check that the sliding roof cannot be operated.
Turn the ignition switch from ON to off and wait for approximately 43 seconds. Check that the sliding roof cannot be operated.
Operate the auto function with the driver or front passenger door open. While the roof glass is moving, turn the ignition switch off. Check that the roof glass stops at the full open/close or full tilt up/down position.
CHECK JAM PROTECTION FUNCTION
- CAUTION:
- ·
Do not use a part of your body, for example, your hand, to check the jam protection function.
·Do not allow anything to become caught in the sliding roof by accident while performing this inspection.
·Perform the inspection from the inside of the vehicle.
- NOTICE:
- ·
Do not use hard objects, such as a hammer, to avoid damaging the roof.
·Make sure that initialization has been completed before inspection.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
·The jam protection function does not operate when the roof glass is close to the fully closed position.
When the slide close function is operating and an object is caught between the vehicle body and roof glass, check that the roof glass opens a distance of 218 mm (8.58 in.) from the point of contact with the object, or opens fully if an opening distance of 218 mm (8.58 in.) is not available.
When the tilt down function is operating and an object is caught between the vehicle body and the roof glass, check that the sliding roof tilts up fully.
CHECK SLIDING ROOF OPEN WARNING FUNCTION
- NOTICE:
- ·
Make sure that initialization has been completed before inspection.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
·The sliding roof open warning can be customized. Make sure that the sliding roof open warning is ON.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>CUSTOMIZE PARAMETERS
Open the sliding roof by using the sliding roof switch (map light assembly).
When the ignition switch is turned from ON to off and the driver door is opened with the key in the vehicle, check that the warning buzzer in the combination meter assembly sounds once. Then, check that the multi-information display in the combination meter assembly displays "MOON ROOF OPEN".