K313 CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33829 1.INSTALL TRANSMISSION CONTROL CABLE SUPPORT

HINT:

Perform this procedure only when replacement of the transmission control cable support is necessary.


a.

Install the transmission control cable support to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the transmission control cable assembly to the transmission control cable support with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


d.
C261988C05
2.896,0.615 3.094,0.792 0.198,0.177 10 *a 2.542,0.146 2.74,0.323 0.198,0.177 10 *b
*a P Position
*b N Position


Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


e.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


f.

Turn the nut of the transmission control cable assembly counterclockwise approximately 180°. While holding the nut in that position, push in the stopper until it clicks twice.

C151676C03
1.219,1.01 1.583,0.51 1.583,0.51 1.688,0.51 false 0.563,2.177 0.667,2.177 0.667,2.177 1.063,1.646 false 1.771,0.417 2.063,0.625 0.292,0.208 10 false *a 0.385,2.094 0.604,2.302 0.219,0.208 10 false *b 3.292,0.594 3.531,0.813 0.24,0.219 10 false *c
*a Stopper *b Nut
*c Push in - -



g.

Install the transmission control cable assembly to the transmission floor shift assembly. Check that the spring is positioned at (A) and push in the stopper.

C270204C02
1.135,0.813 1.333,0.219 1.333,0.219 1.448,0.219 false 3.406,2.458 3.51,2.458 3.51,2.458 3.781,1.813 false 3.51,1.146 4.563,0.406 4.563,0.406 5.906,1.156 false 2.865,1.99 2.969,1.99 2.969,1.99 3.448,1.188 true 5.344,2 5.469,2 5.469,2 5.885,1.219 true 1.354,0.885 1.604,0.615 1.604,0.615 1.729,0.615 false 3.219,2.385 3.448,2.573 0.229,0.188 10 false *1 1.51,0.125 1.771,0.302 0.26,0.177 10 false *a 4.49,0.208 4.719,0.417 0.229,0.208 10 false *b 3.083,0.635 3.344,0.854 0.26,0.219 10 false *d 2.719,1.906 2.844,2.063 0.125,0.156 10 false A 5.177,1.917 5.302,2.073 0.125,0.156 10 false A 1.813,0.521 2.125,0.719 0.313,0.198 10 false *c
*1 Transmission Floor Shift Assembly - -
*a Stopper *b Spring
*c Nut *d Push in


NOTICE:
·

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

·

Make sure that the transmission control cable assembly is securely locked.




h.
C293577

Install the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Install the end of the transmission control cable assembly all the way to the base of the pin.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 3.ADJUST SHIFT LEVER POSITION

Click hereDrivetrain>K313 CVT>TRANSMISSION CONTROL CABLE>ADJUSTMENT

Hide 58151 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the 3 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Click hereEngine / Hybrid System>2ZR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION

Hide 17701 8.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click hereEngine / Hybrid System>2ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION

Hide 17705 9.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Click hereEngine / Hybrid System>2ZR-FE ENGINE CONTROL>THROTTLE BODY>INSTALLATION

Hide 11212 10.INSTALL NO. 2 CYLINDER HEAD COVER

Click hereEngine / Hybrid System>2ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the cable to the negative (-) battery terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION

Hide 13.INSPECT SHIFT LEVER POSITION

Click hereDrivetrain>K313 CVT>SHIFT LEVER>ON-VEHICLE INSPECTION