K313 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  INITIALIZATION  


NOTICE:
·

Performing Reset Memory will clear the learned value of the deceleration sensor zero point calibration and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, deceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Brake actuator assembly (Skid control ECU)

·

Deceleration sensor assembly



·

After performing Reset Memory, always perform deceleration sensor zero point calibration first, and then CVT oil pressure calibration.



RESET MEMORY/CALIBRATION


a.

Perform Reset Memory as follows:

i.

Turn the ignition switch off.


ii.

Move the shift lever to P and apply the parking brake.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

NOTICE:
·

Keep the vehicle stopped, level and stable during the calibration (Inclination: 0 +/- 0.25°).

·

Make sure that the shift lever is in P.

·

Make sure that the engine is stopped. To prevent idling vibrations, do not start the engine.

·

Make sure that the ignition switch is ON.



Powertrain > Engine and ECT > Utility
Tester Display
Reset Memory
50005 234 176


b.

Perform deceleration sensor zero point calibration as follows:

i.

Turn the ignition switch to ON and wait at least 2 seconds.


ii.

Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor Zero Point Calibration.

HINT:
·

When "Complete" is displayed on the screen, deceleration sensor zero point calibration is complete.

·

If "Error" is displayed on the screen and DTC P1589 is output (for the detection conditions for DTC P1589), refer to P1589, the deceleration sensor circuit may be malfunctioning.

Click hereDrivetrain>K313 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P1589

·

Shaking or vibrating the vehicle during deceleration sensor zero point calibration may cancel calibration. If "Error" is displayed on the screen and DTC P1589 is not output, perform calibration again.



Powertrain > Engine and ECT > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 234 2123


c.

Perform CVT oil pressure calibration as follows:

i.

Turn the ignition switch off and wait at least 30 seconds.


ii.

Turn the ignition switch to ON and wait at least 2 seconds.

NOTICE:

Do not start the engine.


HINT:

CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, the calibration cannot be performed under the following conditions:

·

Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or more.

·

CVT oil temperature is 0°C (32°F) or less or 120°C (248°F) or more.




iii.

Start the engine and wait at least 5 seconds.


iv.

Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

HINT:
·

During CVT oil pressure calibration, the engine idle speed will increase.

·

When "Complete" is displayed on the screen, CVT oil pressure calibration is complete.

·

The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.



Powertrain > Engine and ECT > Utility
Tester Display
CVT Oil Pressure Calibration
50005 234 2122