SLIDING ROOF / CONVERTIBLE SLIDING ROOF SYSTEM Sliding Roof does not Move by Operating Sliding Roof Control Switch
DESCRIPTION
The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch (map light assembly) is operated and drives its built-in motor.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
- NOTICE:
- ·
Inspect the fuses for circuits related to this system before performing the following procedure.
·If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
·The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
·If a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
PROCEDURE
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the GTS.
- Body Electrical > Sliding Roof > Data List
-
Tester Display Measurement Item Range Normal Condition Diagnostic Note Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed- Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed- Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed- Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed-
- Body Electrical > Sliding Roof > Data List
-
Tester Display Open Switch Close Switch Up Switch Down Switch - 50003 147 1,4,7,10
- OK:
The GTS display changes according to switch operation as shown in the table.
- Result:
Proceed to OK NG
OK
NG
*a | Front view of wire harness connector
(to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) |
Disconnect the O16 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Condition Specified Condition O16-8 (B) - Body ground Always 11 to 14 V O16-1 (IG) - Body ground Ignition switch ON 11 to 14 V O16-1 (IG) - Body ground Ignition switch off Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition O16-12 (E) - Body ground Always Below 1 Ω
- Result:
Proceed to OK NG
OK
NG
Remove the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
- Result:
Proceed to OK NG
OK
NG
Disconnect the O10 sliding roof switch (map light assembly) connector.
Disconnect the O16 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition O16-5 (CLS) - O10-2 (CLS) Always Below 1 Ω O16-5 (CLS) or O10-2 (CLS) - Body ground Always 10 kΩ or higher O16-7 (OPN) - O10-3 (OPN) Always Below 1 Ω O16-7 (OPN) or O10-3 (OPN) - Body ground Always 10 kΩ or higher O16-6 (DWN) - O10-4 (DOWN) Always Below 1 Ω O16-6 (DWN) or O10-4 (DOWN) - Body ground Always 10 kΩ or higher O16-4 (UP) - O10-5 (UP) Always Below 1 Ω O16-4 (UP) or O10-5 (UP) - Body ground Always 10 kΩ or higher O10-1 (GND) - Body ground Always Below 1 Ω O16-12 (E) - Body ground Always Below 1 Ω
- Result:
Proceed to OK NG
OK
NG